* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
It looks and runs totally different. Satisfaction!
Compared to the OEM Pipe outside diameter Φ38.1, the pipe outside diameter Φ50.8 is overwhelmingly thicker, which makes it look tougher and more powerful. In the accompanying Instruction Manual Removing OEM Parts When you remove the O2 Sensor, please remove the Side cover and pull out the Coupler of the most rear side. But it was the most front side to remove. Idling is not much different, but the popping sound when you puff it up goes away. When I run it, I get regular range power and the acceleration and deceleration feels good. I can feel the ride quality gets better. 3 years have passed since I bought the Rebel in 2005, and the rust was beginning to appear on the front pipe of the OEM, so I replaced it and it became clean.
The replacement work itself can be completed in 30 minutes because it is a single cylinder. I rolled my own heat resistant Vantage to be conscious of its appearance. It is the impression which actually runs, but I felt that the fine fine vibration which came from the area which exceeded 70Km/h was decreased by the use with Exhaust System made by the company. I also felt that the Torque up can start up in 3rd gear, which I always felt like I needed 2.5 gear at intersections. It is not expensive, and I recommend it for its powerful Up effect.View Detail
If you are wearing the Endurance Engine Guard, it will interfere with the Bracket of the Right Side Engine Guard.The lower side of the RightEngine GuardQuantity:I put 3 pieces of Washer between the engine guard and the body side of 2pc Bolt and let it go out a little. Even so, the gap with the exhaust pipe is about 1~2? It seems to be thicker than OEM and slightly closer to Right. Flange fixed nut of Exhaust pipe part is also thicker, because Socket and Glasses interfere with Exhaust pipe, you have to tighten it by inserting Spanner through the gap. You can see the installation video on MORIWAKI Hope Page.View Detail
The replacement work itself can be completed in 30 minutes because it is a single cylinder. I rolled my own heat resistant Vantage to be conscious of its appearance. It is the impression which actually runs, but I felt that the fine fine vibration which came from the area which exceeded 70Km/h was decreased by the use with Exhaust System made by the company. I also felt that the Torque up can start up in 3rd gear, which I always felt like I needed 2.5 gear at intersections. It is not expensive, and I recommend it for its powerful Up effect.View Detail
If you are wearing the Endurance Engine Guard, it will interfere with the Bracket of the Right Side Engine Guard.The lower side of the RightEngine GuardQuantity:I put 3 pieces of Washer between the engine guard and the body side of 2pc Bolt and let it go out a little. Even so, the gap with the exhaust pipe is about 1~2? It seems to be thicker than OEM and slightly closer to Right. Flange fixed nut of Exhaust pipe part is also thicker, because Socket and Glasses interfere with Exhaust pipe, you have to tighten it by inserting Spanner through the gap. You can see the installation video on MORIWAKI Hope Page.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING