Construção em aço com acabamento em preto mate
[Tamanho]
largura : 710
altura : 100mm
voltar : 160mm
Secção da pinça : Φ25.4mm
parte de agarrar : 22.2mm
*É necessário remover do guiador genuíno o aquecedor com punho esquerdo (HONDA PARTE No.35520-MLA-305), que é fixado com uma forte aderência no momento da montagem do novo Rebel 1100 na fábrica da Honda, e é necessário removê-lo e substituí-lo por um novo, dependendo do estado do aquecedor com punho esquerdo genuíno (HONDA PARTE No.35520-MLA-305). No.35520-MLA-305) e substituí-lo por um novo, dependendo do seu estado. Mesmo que o motor seja ligado e o aquecedor do grip seja puxado para fora depois de ter sido aquecido ao máximo, pode falhar no processo de o remover, porque está muito apertado. Se for difícil remover o aquecedor do lado esquerdo (HONDA PARTS Genuine No.35520-MLA-305), terá de comprar um novo aquecedor do lado esquerdo (HONDA PARTS Genuine No.35520-MLA-305) para instalar este produto por si próprio. Nesse caso, haverá uma sobra de volante genuíno e um aquecedor de aderência do lado esquerdo genuíno (HONDA PARTS Genuine No.35520-MLA-305), que será necessário para restaurar ao estado genuíno.
*Existe a possibilidade de se queimar ao remover o aquecedor do lado esquerdo genuíno (HONDA PARTS Genuine No.35520-MLA-305), por isso, por favor, trabalhe com cuidado enquanto protege com luvas, etc.
*Se o aquecedor funcionar mal ou for destruído durante o funcionamento, deve ser substituído por um novo (Honda Parte No. 35520-MLA-305).
*Não há necessidade de mudar a mangueira/harness/fios para este produto, mas se estiver preocupado, poderá ter de mudar a mangueira de travão para um comprimento adequado. Poderá ser necessário ajustar a tensão do travão de estacionamento, etc., devido à alteração do traçado.
*Antes de comprar este produto, não se esqueça de pedir à sua loja Honda Dream para remover o aquecedor genuíno do lado esquerdo (HONDA PARTS GENERAL NO. 35520-MLA-305) e substituí-lo por um novo, dependendo da condição de (HONDA PARTS GENERAL NO. 35520-MLA-305), Se for difícil remover o aquecedor genuíno do lado esquerdo (HONDA PARTS Genuine No.35520-MLA-305), é necessário preparar e instalar um novo aquecedor genuíno do lado esquerdo (HONDA PARTS Genuine No.35520-MLA-305) para instalar este produto. (Honda Parts Genuine No. 35520-MLA-305), e que é necessário ajustar a tensão do travão de estacionamento, etc., ao comprimento adequado.
*Há um erro na espessura da tinta neste produto. Há um caso em que o lado do eixo é baço quando se vira o eixo. Neste caso, é necessário ajustá-lo, raspando a parte do produto da pega com um ficheiro.
*As marcas de socos neste produto são apenas para referência. Por favor, ajuste a posição da pega ao seu gosto.
*Há um caso em que o buraco da caixa de interruptores deste produto está ligeiramente desalinhado. Neste caso, é necessário modificar o buraco, alargando-o.
*Há um caso em que há uma mudança de especificação da mercadoria pela conveniência do fabricante. Por favor, compreendam.
[Size]
・Width: 740mm
・Height: 80mm
・Back: 225mm
・Clamp part: Φ25.4mm
・Grip: 22.2mm
*It is necessary to remove the stock left side grip heater (HONDA PART No.35520-MLA-305) which is fixed with a strong grip bond when assembling the new REBEL 1100 at the HONDA stock from the stock handlebar. No.35520-MLA-305) and replace it with a new one depending on its condition.Even if you start the engine and warm up the grip heater to the maximum and pull it out, it is attached really tightly and it may fail in the process of removal.If it is difficult to remove the stock left side grip heater (HONDA stock parts No.35520-MLA-305), you need to purchase a new stock left side grip heater (HONDA stock parts No.35520-MLA-305) by yourself to install this product.In this case, there will be an extra stock handlebar and a stock left side grip heater (HONDA Parts stock No. 35520-MLA-305), which will be necessary to restore the vehicle to its original condition.
*When you remove the stock left side grip heater (HONDA STOCK PART NO.35520-MLA-305), you may get burned, so please use the glove to protect your hand.
*If the heater fails or is destroyed during operation, it must be replaced with a new one (HONDA Stock Part No. 35520-MLA-305).
*This product does not require any changes to the hoses / harnesses / wires, but if you are concerned, please change the brake hoses to an appropriate length.The parking brake may need to be adjusted due to the change in handling.
*Before purchasing this product, be sure to inform HONDA Dream shop to remove the stock left side grip heater (HONDA Parts Stock NO. 35520-MLA-305) and replace it with a new one depending on the condition of (HONDA Parts Stock NO. 35520-MLA-305), If it is difficult to remove the stock left side grip heater (HONDA Parts Stock No. 35520-MLA-305), it is necessary to prepare and install a new stock left side grip heater (HONDA Parts Stock No. 35520-MLA-305) to install this product. (Honda Parts Stock No. 35520-MLA-305), and that the tension of the parking brake needs to be adjusted, etc. to the appropriate length.
*The thickness of the paint on this product may vary.There may be a dullness when turning to the axle side.In this case, it is necessary to adjust the product part of the handlebar by shaving with a file.
*The punch marks on this product are for reference only.Please adjust the position of the handlebar to your liking.
*The holes in the switch box of this product may be slightly out of alignment.In this case, it is necessary to widen the hole.
*There may be changes in product specifications due to the manufacturer's reasons.