Material] Aço cromado (acabamento em 3 camadas)
*Há um caso em que há uma mudança de especificação da mercadoria pela conveniência do fabricante. Por favor, compreendam.
[Sobre a instalação]
*O eixo do eixo é um componente crítico.
A instalação deve ser realizada por pessoal qualificado numa loja profissional.
Utilizar a ferramenta apropriada para a forma da cabeça do eixo.
Se a haste for apertada com uma ferramenta inadequada, a película de revestimento na superfície da haste será arranhada e a ferrugem será causada.
Antes da instalação, aplicar massa lubrificante ou outro óleo na superfície do eixo.
A superfície da haste é tratada com a "película de revestimento de 3 camadas" original da KOOD, pelo que não ocorrerá ferrugem na própria haste em condições normais de utilização. Isto é para evitar que a ferrugem seja transferida dos rolamentos das rodas, etc., que é causada pela diferença de potencial eléctrico entre os metais.
Por favor, observe o torque de aperto especificado pelo fabricante.
Se o veículo for instalado utilizando a porca genuína, verifique por favor a porca.
Se a porca tiver sido danificada por uma queda ou se a parte auto-travante estiver gasta, não se esqueça de usar uma porca nova. Isto é para evitar danos na parte roscada do eixo.
[Sobre a Qualidade do Produto]
No entanto, se houver algum problema, por favor contacte-nos antes do trabalho.
*Em nenhuma circunstância aceitaremos quaisquer reclamações ou devoluções após a instalação (tais como a passagem do eixo através da roda).
Sobre a ferrugem
Os poços KOOD são tratados com uma "película de revestimento de 3 camadas".
O revestimento é mais forte do que a película de revestimento normal. A ferrugem pode ocorrer em função das condições de utilização, mas não há problema na qualidade.
<The principal causa de ferrugem
Transferência de ferrugem... Ferrugem externa na superfície revestida
Danos no filme de revestimento... Utilização inadequada de ferramentas, degraus durante a condução, quedas, etc.
*Note-se que a ferrugem não é coberta pela garantia de qualidade. Por favor, compreenda de antemão.
[Material] Chromoly steel (3-layer plating finish)
*There may be changes in product specifications due to the manufacturer's reasons.
[About the installation]
*Axle shafts are critical parts.
Installation must be carried out by qualified personnel at a professional shop.
・Please use the appropriate tool for the head shape of the shaft.
If the shaft is tightened with an inappropriate tool, the plating film on the shaft surface will be scratched and rust will be caused.
・Before installation, apply grease or other oil to the shaft surface.
The surface of the shaft is treated with KOOD's original "3-layer plating film", so rust will not occur on the shaft itself under normal use.The purpose is to prevent rust transfer from wheel bearings, etc., which is caused by the potential difference of metals.
・Please observe the tightening torque specified by the manufacturer.
・If the vehicle is installed using the stock nut, please check the nut.
If the nut is damaged by tipping over, etc., or if the self-locking part is worn out, be sure to use a new nut.This is to prevent damage to the shaft threads.
[About Product Quality]
・KOOD has taken all possible measures to manage the production. However, if there is any problem, please contact KOOD before the work.
*In no event will KOOD accept any claims or returns after the installation (such as threading the shaft into the wheel).
・About rust
KOOD shafts are treated with a "3-layer plating film".
It is processed with a stronger film than normal plating film.Rust may occur depending on the usage conditions, but there is no problem with the quality.
・Transferred rust: Rust from the outside gets on the plated surface
・Damage to the plating film... Improper use of tools, flying rocks during riding, falls, etc.
[Caution]
In case of KOOD shafts with plated nuts, damaging the threads during installation often happens.
Due to the nature of plating, this is often seen when the plated parts (e.g. KOOD shaft and KOOD nut) mesh with each other or when the threaded part is greaseless.
Please use an anti-corrosive grease such as sledge compound on the screw part when you install it.