Sensor 3G digital de alto desempenho!
É um kit apenas para o modelo de carro do alarme de roubo de um vendedor de longa duração que é fácil de usar mesmo para um principiante..
Não é necessário controlo remoto. A configuração só pode ser facilmente libertada se se accionar a chave de ignição ON/OFF!
O sensor digital 3G emite um alarme de 122db quando a atitude do veículo muda em mais de 5 graus..
A característica do kit é que vem com instruções sobre onde instalar o sensor, sirene, e LED indicador, bem como instruções sobre como ligar os fios, para que possa facilmente instalá-lo sem se preocupar com a colocação de cada peça, ao contrário dos kits de uso geral..
A cablagem do próprio sensor foi ajustada ao comprimento apropriado para o modelo de carro, para que possa ser instalada de forma limpa sem que a cablagem longa desnecessária se interponha no caminho..
O alarme pode ser facilmente accionado tanto no suporte lateral como no suporte central..
[instruções de instalação]
Retirar o assento e a tampa do lado esquerdo..
Fixar o corpo do sensor CS-550M no estande que segura a bateria, e ligar o fio vermelho do corpo do sensor ao lado positivo da bateria e o fio preto ao lado negativo.. O corpo principal do sensor é fixado com fita adesiva de dupla face, mas pode ser fixado com uma fita adesiva para evitar avarias..
O lado positivo tem uma capa de borracha vermelha, por isso se passar o cordão vermelho como mostra a imagem, pode cobrir bem a capa de borracha..
O altifalante é ligado ao lado exterior da caixa da bateria na tampa do lado esquerdo e ligado ao próprio sensor..
Retirar a tampa da parte de trás do pára-lamas traseiro.. O círculo amarelo tem dois parafusos, e o círculo vermelho tem dois rebites de pressão.. Retire-os todos e a tampa sairá..
Há um acoplador 3P impermeável da lâmpada traseira na tampa de borracha translúcida circundada a vermelho na imagem.. A cablagem é um acoplador à prova de água com três fios preto, verde e verde/amarelo, para que o saiba de imediato!.
Ligar o cabo laranja do corpo do sensor ao cabo preto da lâmpada traseira com uma torneira eléctrica..
A luz indicadora é ligada ao quadro entre o tanque e a ponte superior.. Ligar o cordão do corpo do sensor e voltar a juntar o assento e a tampa do lado esquerdo para completar o trabalho..
Demora cerca de 30-40 minutos a chegar à casa.. A posição de instalação do sensor e da sirene é mostrada no manual de instruções, por isso é muito fácil!.
[manual de instruções].
1) Parar o motor com a tecla OFF..
2) Ligue a chave e desligue-a imediatamente.
3) Ouve-se um breve sinal sonoro, e a luz indicadora vermelha brilha durante 0,5 segundos, e depois apaga-se durante 2 segundos..
4) O alarme foi agora activado..
A sirene não soará durante cerca de 1 minuto após o alarme ser accionado, mas a lâmpada indicadora piscará a alta velocidade..
Quando uma anomalia é detectada após um minuto, a lâmpada indicadora pisca a alta velocidade e a sirene emite um som de alarme alto de 122db..
■High performance digital 3G sensor!
・This is a special kit for a long-selling burglar alarm that is easy to use even for beginners.
・No remote control required.The setting can be easily canceled only by operating the ignition key ON / OFF!
・The digital 3G sensor sounds a 122dB alarm when the vehicle's attitude changes by more than 5 degrees.
・The feature of the kit is that it comes with instructions on where to install the sensor, siren, and indicator LED, as well as instructions on how to connect the wires, so you can easily install it without worrying about the placement of each part, unlike universal kits.
・The wiring of the sensor itself has been adjusted to the appropriate length for the model of vehicle, so it can be installed neatly without unnecessary long wiring getting in the way.
・The alarm can be easily set on either the side stand or center stand.
[installation instructions]
・Remove the seat and the left side cover.
・Attach CS-550M sensor unit on the bracket holding the battery, and connect the red cord of the sensor unit to the positive side of the battery and the black cord to the negative side.The sensor body is attached with double-sided tape, but it is recommended to fix it with a bundle band to prevent malfunction.
・There is a red rubber cover on the plus side, so if you put the red cord through as shown in the image, you can cover the rubber cover nicely.
・The speaker is attached to the outer side of the battery case in the left side cover and connected to the sensor itself.
・Remove the cover from behind the rear fender.The yellow circles have two screw locations, and the red circles have two push rivets.Remove them all and the cover will come off.
・The waterproof 3P coupler of the taillight is located in the translucent rubber cover circled in red in the image.The wiring is a waterproof coupler with three wires (black, green, and green / yellow), so it should be easy to find.
・Connect the orange cord of the sensor to the black cord of the taillight with an electro tap.
・Attach the indicator light to the frame between the tank and the top bridge.Connect the cord of the sensor body, and put the seat and the left side cover back together to complete the work.
・It takes about 30-40 minutes to get here.The installation position of the sensor and siren is shown in the instruction manual, so it is very easy.
[operating instructions]
1) Stop the engine with the key OFF.
2) Turn the key ON and immediately turn it OFF.
3) A short beeping sound is heard, and the red indicator light shines for 0.5 seconds, then goes out for 2 seconds, and the operation is repeated.
4) The alarm is set.
The siren will not sound for about one minute after the alarm is set, even if it detects an abnormality, but the indicator lamp will flash at high speed.
When an abnormality is detected after one minute, the indicator lamp flashes rapidly and the siren emits a loud alarm sound of 122db.