Esta é a gola que permite instalar o braço oscilante para Suzuki GSX750S Katana 1100S Katana no CB750FZ..
O braço oscilante Katana é o mesmo para ambos os lados, em oposição ao braço oscilante assimétrico CB-F..
Para resolver este problema, alterámos a largura da gola do lado esquerdo e direito para compensar o braço oscilante da catana..
Tanto o centro da roda como a linha da corrente estão na posição correcta para permitir a instalação aparafusada às rodas e travões de stock CB-F..
O colarinho que ajusta a posição do braço oscilante é feito de aço para resistência e a superfície é chapeada para evitar a ferrugem..
Além disso, é adoptado um colarinho endurecido para a parte portadora da agulha..
Se mudar para braço oscilante Katana, pode usar roda CB750F/CB900F, colarinho de roda, suporte de calibre e haste de torque..
O eixo pivot é para CB750FZ e o eixo eixo é para CB-F e Katana..
Também, usar a tampa do braço oscilante, a gola interna do pivot e o ajustador de corrente para os Katana..
O manual de instruções está incluído.
[Sobre a largura do casquilho da peça de suporte da suspensão do braço oscilante].
Por favor substituir o casquilho da suspensão pelo casquilho genuíno para CB-F. Ou, se utilizar o casquilho para Katana, por favor reduzi-lo para 19mm de largura.. (*Ver imagem 5)
*Existem dois números de peça genuínos para CB-F, 40548-268-000 [para CB750FZ] e 52451-357-000 [para CB750FA-FC], mas ambos podem ser utilizados..
(A largura da circunferência exterior do arbusto é para CB750FZ(18mm) e para CB750FA-FC(16mm), mas a largura(19mm), o diâmetro interior(10mm) e o diâmetro exterior(22mm) do centro do arbusto são os mesmos para ambos os arbustos).
This is a collar which enables to install Suzuki GSX750S Katana 1100S Katana swingarm on CB750FZ.
The Katana swingarm is designed to be used with the asymmetrical CB-F swingarm.
To solve this problem, the width of the left and right collar is changed to offset the Katana swingarm.
Both the wheel center and chain line are correctly positioned to allow bolt-on installation to the stock CB-F wheels and brakes.
The collar to adjust the position of swingarm is made of steel for strength and plated surface to prevent rusting.
In addition, a hardened collar is used for the needle bearing part.
If you change to Katana swingarm, wheel, wheel collar, caliper support and torque rod of CB750F / CB900F can be used.
Pivot shaft is for CB750FZ and axle shaft for CB-F and Katana are both usable.
The cap of the swingarm pivot, the collar inside the pivot and the chain adjuster must be used for Katana.
Comes with an instruction manual.
[About the bushing width of the swingarm suspension support part]
The bushing of the suspension support should be replaced with the stock bushing for CB-F. Or, if you use the bushing for Katana, cut it down to 19mm width.(*See image 5)
*The stock bushing part number for CB-F is 40548-268-000 [for CB750FZ] and 52451-357-000 [for CB750FA-FC], both of them can be used.
(The width of the outer circumference of the bush is for CB750FZ (18mm) and for CB750FA-FC (16mm), but the width (19mm), inner diameter (10mm) and outer diameter (22mm) of the center of the bush are the same for both bushes)